Ignition/Distributor Engine Speed Input Circuit Range/Performance


The PCM has detected an input signal from either the crankshaft position sensor or the distributor that has been interrupted, is erratic, or in some way abnormal. The position of the crankshaft and distributor are typically determined by the PCM to be misaligned when this code is stored.

Code Set Parameters

If the crankshaft position sensor and distributor position sensor are not within a predetermined number of degrees of variation, a code will be stored and a malfunction indicator lamp may be illuminated. Some models require multiple failure cycles on order for a service engine soon lamp to be illuminated.


Symptoms may range from none at all to an engine that cranks and the stalls, a hard starting engine, engine hesitation r misfire, and possibly service engine soon lamp illumination.

Common Causes

The most common cause of this code may include a defective crankshaft/camshaft position sensor, CPS wiring, or CPS electrical connector. A faulty distributor sensor, distributor, or respective wiring circuitry may also contribute to the conditions associated with this code being stored.

Common Misdiagnosis

Replacement of any sensors without first diagnosing engine misfires can lead to an incorrect diagnosis. Because of the possibility of variations in crankshaft, camshaft, and distributor sensor voltage caused by a misfiring engine, engine misfires must be diagnosed and repaired prior to diagnosing this code.


  • Manufacturers utilize the electro-magnetic crankshaft position sensor in two different manners
  • Both designs use either a reluctor ring or teeth (attached to the crankshaft) to interrupt the field of the stationary electro-magnetic CSP sensor; creating what is interpreted by the PCM as a square wave form pattern
  • These interruptions provide the PCM with the precise crankshaft position
  • In the first design, the PCM uses the crankshaft position only for misfire detection and is not critical to spark timing or ignition
  • Engine control systems that use this type of system may allow the engine to start and run, despite a crankshaft position circuit failure, but engine performance and fuel economy will likely suffer
  • Malfunction indicator lamp illumination may not occur until multiple failures are documented in this type of system
  • In the second type of system the PCM uses crankshaft position to calculate spark timing and ignition control
  • A crankshaft position sensor failure in this system design will normally lead to a no-start condition, an immediate stored trouble code, and an illuminated service engine soon lamp (on the first failure). Several specialty tools will be required to diagnose this code successfully
  • They include a scanner, a digital volt/ohmmeter, and possibly an oscilloscope
  • Begin your diagnosis with a visual inspection of all wiring and connectors
  • Repair or replace damaged, disconnected, shorted, or corroded wiring, connectors, and components as necessary
  • Always retest the system after repairs are completed to ensure success. If all system wiring, connectors, and components (Including fuses) appear to be in normal working order, connect the scanner (or code reader) to the diagnostic connector and record all stored codes and freeze frame data
  • This information can be extremely helpful in diagnosing intermittent conditions that may have contributed to this code being stored
  • Continue by clearing the code and operating the vehicle to see if it returns
  • This will help to determine whether or not the malfunction is intermittent
  • After the codes are cleared, test drive the vehicle to see if the code returns
  • If the code fails to immediately return, you may have an intermittent condition
  • Intermittent conditions can prove to be quite a challenge to diagnose and in extreme cases may have to be allowed to worsen before a correct diagnosis can be made
  • In the event of an intermittent condition, you may also utilize the oscilloscope to monitor waveforms created by the distributor, camshaft, and/or crankshaft sensor/s, while looking for glitches or other inconsistencies. A viable starting point for obtaining a successful diagnosis of the crankshaft position sensor is by checking for an engine RPM signal when the engine is cranked or running
  • This is accomplished by using a scanner or observing the vehicle tachometer as the engine is being cranked (using the starter) or is running, depending upon CPS system design
  • If no RPM signal is detected, then visually inspect the crankshaft gear, crankshaft position sensor, and sensor connector for damage and repair as necessary
  • If no obvious signs of damage are found, then test the CPS system for a reference voltage signal (typically 5-volts, but check manufacturer’s specifications)
  • If you have access to an oscilloscope, then test the CPS signal wire for the presence of a square 5-volt waveform pattern for each engine revolution
  • If no pattern is detected then test the resistance of the (disconnected) CSP sensor and compare the values with manufacturer’s specifications
  • If the CSP sensor checks out, then test the system circuitry for the proper voltage and resistance
  • Repair open or shorted wiring as necessary
  • While PCM failure is certainly a possibility, it is rare and all other possibilities should be exhausted prior to condemning the PCM. The camshaft position sensor and distributor hall-effect sensor are used in a similar manner to the crankshaft position sensor
  • Inputs between the three sensors help to control ignition timing and fuel delivery. The camshaft position sensor is an electro-magnetic sensor that interacts with a metal reluctor ring (or gear) on one end or the other of the camshaft
  • Engines that utilize multiple camshafts (dual-overhead cam engines) are equipped with multiple camshaft position sensors
  • As the reluctor passes by the sensor, a precisely placed hole or gap in the teeth interrupts the waveform pattern sent by the sensor to the PCM
  • This interruption correlates with an ignition timing reference value that is programmed into the PCM
  • Variations from the manufacturer’s reference timing value (seen as voltage waveforms) will cause a code to be stored and possibly a malfunction indicator lamp to be illuminated. If the code returns, begin with a visual inspection of distributor, camshaft and crankshaft position sensor system wiring and electrical connectors
  • Suspect areas of system circuitry that are contaminated with oil, antifreeze, or power steering fluid that has leaked from the engine
  • If wiring with missing or distorted insulation is found, repair or replace it as necessary. If no obvious system circuitry problems are discovered, perform a resistance test at the crankshaft, camshaft, and distributor position sensors and a voltage test on the sensor connector
  • Using your digital volt/ohmmeter test reference voltage at the sensors and compare your findings with the manufacturer’s specified reference voltage
  • If system reference voltage readings are in line with specified values (or if sensor resistance values do not coincide), replace the camshaft sensor, distributor hall-effect sensor, and the crankshaft sensor. If system voltage readings do not coincide with manufacturer’s specified reference figures, check system continuity using your digital volt/ohmmeter
  • Use caution when checking resistance values in wiring that is connected to the PCM
  • For best results, disconnect the electrical connector from the PCM prior to using an ohmmeter on the harness side of the circuit
  • Remember that PCM failure is possible but very rare